Editorial
  • RSS FeedSubscribe to RSS feed
  • Email to a FriendEmail to a friend
  • PrintPrint article

A Unique Perspective – Photographing from a Floating Blind

by Steve Gettle | March 20, 2013

© Al CharnleyThe sun won’t be up for another hour on this cold crisp March morning in Southern Michigan. It has taken three trips to carry my gear down to the water’s edge. As I begin to assemble my craft by the narrow beam of my headlamp, I hear splashes and the rustling of my quarry from the other side of the pond. I step into my neoprene hip waders; they feel especially snug today, since I am wearing two pairs of long underwear beneath my jeans on this chilly morning. A heavy jacket, gloves, and a woolen hat finish off my uniform. I step into the water, and as I close the blind around me the darkness is complete with the exception of the faint shafts of light coming through the peepholes strategically placed in the canopy. I begin to work my way out into the pond; I try to be as quiet as possible, as my craft breaks through the thin skiff of ice that has formed overnight around the pond’s edges. Progress is slow not only because the muck sucks at my feet with every step, but also because I have to work my way around the fallen trees and limbs hidden beneath the water. I wade out until the water is up to the middle of my chest. This puts the camera mounted on the deck at eye-level. I finally make my way to the other side of the pond and I wait—I wait for my quarry to accept my blind and I wait for the light.

Floating photography blind © Steve Gettle

If this sounds like fun to you, then you must be a nature photographer, and you really should consider building a floating blind. A floating blind is basically a floating deck with a canopy designed to resemble a muskrat house. The deck of the craft has a hole where the photographer stands allowing him to walk along the bottom of the pond. The camera is placed on a tripod head mounted directly on the deck of the “boat” in front of the photographer. I use my floating blind mostly in the spring to photograph waterfowl as they pass through southern Michigan on their race north to find nesting sites. However I have also photographed turtles, white-tailed deer, raccoons, and even turkey as they have fed along the edge of the water.

Frame of floating camera blind © Steve Gettle

There are many things I love about the floating blind. First, unlike most blinds this one is mobile and allows the photographer to actively pursue the subject. This mobility also gives the photographer the ability to easily change backgrounds and the freedom to work the direction of the light to their best advantage. Furthermore, animals are quite a bit less wary when being approached from the water, due to the fact that with the exception of alligators, not too many predators attack from the water. Lastly, and in my opinion the best thing about working from a floating blind is since the camera is mounted directly on the deck of the blind, the lens is just a few inches above the surface of the water. This low angle of view gives the images depth by separating the subject from the background. In addition and even more important to my personal aesthetic, this eye level view lends an intimacy to your images that is very hard to achieve in any other way.

Low-angle bird photography © Steve Gettle

Unless the birds have been acclimated to you and the blind I would recommend a 400mm or greater lens for this type of photography. I generally use my 600mm and will often add the 1.4 tele-converter if I need more reach. That being said, I have had ducks come up and peck at the base of my blind. In fact one day in North Dakota a beaver tried to climb on top of my “muskrat house”. I can tell you when he slapped his tail on the water in frustration it certainly got my attention.

Waterfowl © Steve Gettle

Since I am often shooting with a long lens and I am not mounted on a tripod good technique is absolutely necessary for sharp pictures. I try to keep my shutter speeds as high as possible and when I fire the camera I use my elbows to apply some downward pressure to the deck of the blind to help steady everything. Obviously vibration reduction is a huge asset for this type of photography. I have found that when necessary I am able to shoot shutter speeds as slow as 1/125th with a 600 and a 1.4 tele-converter (1260mm 35mm equivalent) by using vibration reduction and excellent technique. I also try to work in protected bays to avoid wind causing waves that would rock the blind too much.

Small mammal © Steve Gettle

I have to admit that a few years ago I would have never believed that I would actually look forward to the ice going off the lakes. So that I could get up hours before dawn and go out and spend eight hours standing up to my armpits in ice water photographing waterfowl and other wildlife. But as many of you are probably already aware, you only feel the cold until you start shooting!

Construction

The construction of a floating blind is fairly straightforward. The deck is constructed from two layers of 1½” rigid foam insulation, which is sandwiched between two sheets of ¼ inch marine plywood. Begin by ripping a piece of 1×4 down to the thickness of the two stacked pieces of rigid foam insulation. Run these pieces of wood vertically around the outside length of the boat as well as around the inside of the cockpit to add stability to the deck, these 1x4s will also be the anchor for the screws used to hold the plywood deck and plywood base to your craft. The screws along with construction adhesive are what hold the deck together. To add rigidity to where the tripod head will be mounted remove a 4×4 section of the foam interior and replace the foam with a piece of 4×4 lumber using a 1/4×20 bolt that runs through the center of this 4×4 and the entire thickness of the deck. Leave approximately ½” of thread exposed for mounting the tripod head. A gimbal type head is preferable for this type of photography but a ball head would also work well.

Ruddy duck © Steve Gettle

The upright curved canopy supports are made from ½” CPVC water pipe. The ends of these slip into copper water pipe T’s which are attached to the plywood deck. Use 3/16” aluminum rods to provide the horizontal supports for the canopy structure. Slip these rods into holes drilled into the CPVC tubing. It is important to measure these horizontal supports carefully because it is the tight fit of these rods that holds the entire canopy frame in place. I have fiber glassed the entire deck of my blind. This certainly is not necessary and nearly doubles the weight of the blind. But the craft is still light enough that I am able to throw it on the luggage rack on top of my vehicle.

Floating photography blind in use © Al Charnley

Finally the canopy itself is made from camouflage material custom sewn to fit the blind. I had a seamstress sew mine, but if you are handy with a needle and thread you certainly could do this yourself. Once you have created the basic shape for the canopy, support the entire blind with two sawhorses, then place the fabric on the blind. From below crawl into the cockpit and mark the location of the peepholes and opening for the lens snout on the cover. When marking the location of the snout, prioritize for movement up and down because the entire blind is able to swing side to side for lateral movement. The canopy must be fairly tight because any flapping material will scare your subject. Attach two inch Velcro to hold the cover down to the deck by sewing one side of the Velcro to the bottom of the canopy and using epoxy to adhere the other half of the Velcro to the sides of the deck. Finally, install a heavy duty zipper over the cockpit hole in the deck to allow access into the blind.

Good luck and good light!

Steve

About the Author

Steve Gettle's images communicate his love for the wildlife and wild places of our world. For nearly thirty years, he has spent countless hours creating hundreds of thousands of photographs of the beauty around us.

His images have been exhibited in galleries and museums all over the world. Steve has been honored with a one man show at The National Center for Nature Photography in Ohio. Represented by Minden Pictures his work has been featured in many books, magazines, and calendars by The National Geographic Society, Canadian Geographic, Audubon, Sierra Club, The BBC, The World Wildlife Fund, The National Wildlife Federation, Birder’s World, Nature’s Best, Natural History, and many others.

Steve especially enjoys sharing his knowledge through the art of teaching. He teaches through his one day seminar "The Art of Nature Photography" and by leading workshops and photo tours all over the world. Although he travels extensively, he finds much of his inspiration in the natural areas surrounding his home, in Brighton, Michigan.

Visit Steve's website at www.stevegettle.com and his Facebook page for features such as Photo Tip Friday and Photo of the Week www.facebook.com/steve.gettle.

5 thoughts on “A Unique Perspective – Photographing from a Floating Blind

  1. Hey Steve! I remember you telling me about your blind and i still say it’s too skinny for an all day excursion. None the less I can only say it’s the best way to get into the subjects lives on a pond and not only will a photog get great images, but also will experience a very spiritual high from the endeavor. Hope to catch up with you again sometime–

    Paul

  2. Your willingness to “go the extra mile” and to share is commendable and appreciated. I to have always liked the low angle because it more resembles how other creatures see. Thanks.

Post a Comment

Logged in as Anonymous